#!/bin/sh
# vim: syntax=sh
#
# usb.rc	This brings the USB subsystem up and down safely.
#
# $Id: usb.rc,v 1.28 2004/09/20 22:30:35 kroah Exp $
#
# Best invoked via /etc/init.d/hotplug or equivalent, with
# writable /tmp, /usr mounted, and syslogging active.
#
# Bus management is basically unrelated to runlevel changes; it
# relates to physical topology, including possibly hotpluggable
# busses (USB, Cardbus) or controllers.  If a bus is physically
# present, it should normally be available.
# 
# USB-dependant systems (iMacs, "legacy free" x86 systems, and so on)
# should statically link USB keyboard support into the kernel (USB core,
# EHCI/OHCI/UHCI/..., hid, input, keybdev; and likely mousedev) so the
# system console can't be removed by accident.


PATH=/sbin:/bin:/usr/sbin:/usr/bin

unset I_WANT_A_BROKEN_PS
PS_PERSONALITY=linux

HCD=
STATIC_MODULE_LIST=
X11_USBMICE_HACK=false

# override any of the defaults above?
if [ -f /etc/sysconfig/usb ]; then
    . /etc/sysconfig/usb
fi
if [ -f /etc/conf.d/usb ]; then
    . /etc/conf.d/usb
fi


MOUSE_MODULES="mousedev input"

# In its currently-recommended configuration, XFree86 3.3.6 always opens
# /dev/input/mice; so mousedev and input must be loaded before X11 starts.
if [ $X11_USBMICE_HACK = true ]; then
    STATIC_MODULE_LIST="$MOUSE_MODULES $STATIC_MODULE_LIST"
fi


#
# "COLD PLUG" ... recovery from partial USB init that may have happened
# before the OS could really handle hotplug, perhaps because /sbin or
# $HOTPLUG_DIR wasn't available or /tmp wasn't writable.  When/if the
# /sbin/hotplug program is invoked then, hotplug event notifications
# get dropped.  To make up for such "cold boot" errors, we synthesize
# all the hotplug events we expect to have seen already.  They can be
# out of order, and some might be duplicates.
#
# Note that on 2.5 the init filesystem may have loaded some of the more
# essential usb drivers (maybe usb-storage for a boot disk, and hid),
# but we may still need to load less important ones or invoke setup
# scripts that couldn't run earlier.
#
usb_boot_events ()
{
	#
	# FIXME on 2.5, /sys/bus/usb/devices/* gives all of the
	# info we need.  Interface hotplug events come from the
	# "*:*" files, and device events (do them first) come
	# from the others. 
	#
	# don't expect usbmodules to exist!!  and remove the
	# dependency (below) on usbfs to decide whether we should
	# be synthesizing coldplug events.
	#

	# synthesize hotplug events if we can 

	# make sure the usb agent will run
	ACTION=add
	PRODUCT=0/0/0
	TYPE=
	INTERFACE=
	DEVPATH=
	DEVFS=/proc/bus/usb
	DEVICE=
	export ACTION PRODUCT TYPE INTERFACE DEVPATH DEVFS DEVICE

	if [ -d /sys/bus ]; then
	    if [ -d /sys/bus/usb/devices ]; then
		cd /sys/bus/usb/devices
		for device in /sys/bus/usb/devices/[0-9]*; do
		    devlink=$( readlink -f $device )
		    DEVPATH=${devlink#/sys}
		    if [ -f $devlink/../idVendor ]; then
			PRODUCT="$(cat $devlink/../idVendor)/$(cat $devlink/../idProduct)/$(cat $devlink/../bcdDevice)"
		        if [ -f $devlink/../../devnum ]
			then
			    devbus=$( ( echo -n 000 ; cat $devlink/../../devnum ) | sed 's/.*\(...\)$/\1/' )
			    devdev=$( ( echo -n 000 ; cat $devlink/../devnum ) | sed 's/.*\(...\)$/\1/' )
			    DEVICE="/proc/bus/usb/$devbus/$devdev"
			else
			    DEVICE=
			fi
			/etc/hotplug/usb.agent
		    fi	
		done
	    fi
	else
	    # we need (non-bash) programs to parse descriptors.
	    LISTER=`which usbmodules`
	    if [ "$LISTER" = "" ] || [ ! -f /proc/bus/usb/devices ]; then
		echo $"** can't synthesize root hub events"
		return
	    fi
	    for DEVICE in /proc/bus/usb/*/*; do
		/etc/hotplug/usb.agent
	    done
	fi
}


maybe_start_usb ()
{
    COUNT=0

    # if USB is partially initted then synthesize "cold plug" events. the
    # kernel probably dropped many "hot plug" events, and those it didn't
    # drop likely couldn't trigger all the setup actions (kicking daemons,
    # dropping config records, and so on).

    # if it's not initted at all (no hcds loaded) no synthesized events
    # will be needed, we'll see real ones.  knowing that there are no
    # hcds available through version-portable logic is a nightmare, so
    # assume we synthesize unless "usbfs" is clearly not initted (which
    # we currently need when synthesizing, anyway).

    SYNTHESIZE=true
    if [ ! -d /proc/bus/usb ]; then
	SYNTHESIZE=false
    fi

    # if distro hasn't already done part of this ... load core,
    # and mount usbfs before the first hotplug agent fires
    # (so it'll be available to the agents).
    modprobe -q usbcore >/dev/null 2>&1
    if [ -d /proc/bus/usb ]; then
	# if it's not mounted, try to mount it
	if [ -z "`grep " /proc/bus/usb " /proc/mounts`" ]; then
	    if grep -q -E "^[^#][^[:space:]]+[[:space:]]+/proc/bus/usb/?[[:space:]]" /etc/fstab; then
		mount /proc/bus/usb
	    else
		if grep -q usbfs /proc/filesystems; then
		    mount -t usbfs usbfs /proc/bus/usb
		else
		    mount -t usbdevfs usbdevfs /proc/bus/usb
		fi
	    fi
	fi
    fi

    # Load Host Controller Drivers (HCDs) ... this automatically handles
    # systems with multiple controllers (EHCI, OHCI, UHCI) without needing
    # /proc or tools (lspci -v|grep USB, etc) to do so.  If hotplugging
    # is enabled on this system, initting a root hub will cause hotplug
    # events to fire for every device on the tree at that root.

    # FIXME: some of this should be driven by PCI hotplugging, and have
    # the blacklist control which uhci driver gets used (before 2.5).

    # If the user specified which HCD they want, trust them.
    if [ -n "$HCD" ]; then
        modprobe -q $HCD >/dev/null 2>&1
    else
        # "new style" HCDs ... more common code
        modprobe -q ehci-hcd >/dev/null 2>&1
        modprobe -q ohci-hcd >/dev/null 2>&1
        modprobe -q uhci-hcd >/dev/null 2>&1
    
        # "old style" HCDs ... more driver-specific bugs
        modprobe -q usb-ohci >/dev/null 2>&1
        # NOTE: this prefers "uhci"; you may prefer "usb-uhci".
        # modprobe -q usb-uhci >/dev/null 2>&1 || modprobe -q uhci >/dev/null 2>&1
        modprobe -q uhci >/dev/null 2>&1 || modprobe -q usb-uhci >/dev/null 2>&1
    
        # ... add any non-PCI HCDS here.  Examples include the
        # CRIS usb-host, Philips ISP-1161, Symlogic 811HS, and so on.
        # ohci-hcd can handle some non-pci variants.
    fi

    if [ -d /proc/bus/usb ]; then
	# If we see there are no busses, we "failed" and
	# can report so even if we're partially nonmodular.
	#
	# NOTE: this fails on older kernels, where usbdevfs had two files
	# ('devices' and 'drivers') with no hcds registered, but works on
	# newer kernels where usbfs has zero files until hcds register,
	# and might not have the 'drivers' file.
	COUNT=`ls /proc/bus/usb | wc -l`
	if [ $COUNT -lt 2 ]; then
	    umount /proc/bus/usb
	    rmmod usbcore >/dev/null 2>&1
	    return 1
	fi

    # if USB is fully modular and yet can clean up,
    # we know init failed without needing usbfs
    elif rmmod usbcore >/dev/null 2>&1; then
	return 1
    fi

    # hotplug events didn't fire during booting;
    # cope with devices that enumerated earlier
    # and may not have been fully configured.
    if [ $SYNTHESIZE = true ]; then
	sleep 1
    	usb_boot_events
    fi

    # Some modules are statically loaded, perhaps because they are
    # needed to activate filesystem device nodes.
    for MODULE in $STATIC_MODULE_LIST; do
	modprobe $MODULE
    done

    # we did everything we could ...
    return 0
}

maybe_stop_usb ()
{
    # call this multiple times if you had to take down components of the
    # USB subsystem by hand; it cleans up whatever can
    # be cleaned up, letting the system quiesce further.

    # NOTE:  this list of "all USB modules" is unfortunate, but it seems
    # inevitable until modutils supports the notion of drivers with use
    # counts of zero that shouldn't be removed until after their device
    # gets removed.  Maybe in 2.5 ... of necessity, the list is partial.

    # disconnect all controllers we can, and kernel drivers
    # HCDs first, so most drivers reduce their use counts.
    rmmod ehci-hcd >/dev/null 2>&1
    rmmod ohci-hcd >/dev/null 2>&1
    rmmod uhci-hcd >/dev/null 2>&1
    rmmod usb-ohci >/dev/null 2>&1
    rmmod usb-uhci >/dev/null 2>&1
    rmmod     uhci >/dev/null 2>&1

    # user mode code may keep usbfs busy for a while yet ...

    # OK, usbcore won't actually be removed unless there happen to be
    # no USB drivers loaded, and usbfs isn't mounted.  let's force
    # removal of autocleanable modules before trying to rmmod usbcore
    rmmod -as
# note: module-init-tools 0.8a doesn't handle "-as" flags

    # Now let's workaround the fact that some USB modules never increase
    # their module use counts, so that "rmmod -a" won't unload them.
    # (And we can't use "modprobe --autoclean" anyway.)
    rmmod acm              >/dev/null 2>&1
    rmmod audio            >/dev/null 2>&1
    rmmod auerswald        >/dev/null 2>&1
    rmmod belkin_sa        >/dev/null 2>&1
    rmmod bluetooth        >/dev/null 2>&1
    rmmod catc             >/dev/null 2>&1
    rmmod CDCEther         >/dev/null 2>&1
    rmmod cpia_usb         >/dev/null 2>&1
    rmmod cyberjack        >/dev/null 2>&1
    rmmod dabusb           >/dev/null 2>&1
    rmmod dc2xx            >/dev/null 2>&1
    rmmod digi_acceleport  >/dev/null 2>&1
    rmmod dsbr100          >/dev/null 2>&1
    rmmod emi26            >/dev/null 2>&1
    rmmod empeg            >/dev/null 2>&1
    rmmod ftdi_sio         >/dev/null 2>&1
    rmmod hci_usb          >/dev/null 2>&1
    rmmod hid              >/dev/null 2>&1
    rmmod hpusbscsi        >/dev/null 2>&1
    rmmod ibmcam           >/dev/null 2>&1
    rmmod iforce           >/dev/null 2>&1
    rmmod io_edgeport      >/dev/null 2>&1
    rmmod ipaq             >/dev/null 2>&1
    rmmod ir-usb           >/dev/null 2>&1
    rmmod irda-usb         >/dev/null 2>&1
    rmmod kaweth           >/dev/null 2>&1
    rmmod keyspan          >/dev/null 2>&1
    rmmod keyspan_pda      >/dev/null 2>&1
    rmmod kl5kusb105       >/dev/null 2>&1
    rmmod mct_u232         >/dev/null 2>&1
    rmmod mdc800           >/dev/null 2>&1
    rmmod microtek         >/dev/null 2>&1
    rmmod omninet          >/dev/null 2>&1
    rmmod ov511            >/dev/null 2>&1
    rmmod pegasus          >/dev/null 2>&1
    rmmod pl2303           >/dev/null 2>&1
    rmmod printer          >/dev/null 2>&1
    rmmod pwc pwcx         >/dev/null 2>&1
    rmmod rio500           >/dev/null 2>&1
    rmmod rtl8150          >/dev/null 2>&1
    rmmod scanner          >/dev/null 2>&1
    rmmod se401            >/dev/null 2>&1
    rmmod stv680           >/dev/null 2>&1
    rmmod usbhid           >/dev/null 2>&1
    rmmod usbkbd           >/dev/null 2>&1
    rmmod usbmouse         >/dev/null 2>&1
    rmmod usbnet           >/dev/null 2>&1
    rmmod usbtest          >/dev/null 2>&1
    rmmod usb-storage      >/dev/null 2>&1
    rmmod uss720           >/dev/null 2>&1
    rmmod vicam            >/dev/null 2>&1
    rmmod visor            >/dev/null 2>&1
    rmmod wacom            >/dev/null 2>&1
    rmmod whiteheat        >/dev/null 2>&1

    if [ "$STATIC_MODULE_LIST" != "" ]; then
	rmmod $STATIC_MODULE_LIST >/dev/null 2>&1
    fi

    # remove the helper modules that some usb modules need
    rmmod usbserial        >/dev/null 2>&1
    rmmod usbvideo         >/dev/null 2>&1

    # ok, hope that user mode drivers/managers closed their fds.
    umount /proc/bus/usb >/dev/null 2>&1

    rmmod usbcore >/dev/null 2>&1

    # we did everything we could ...
    return 0;
}

# See how we were called.
case "$1" in
  start)
	maybe_start_usb
        ;;
  stop)
	maybe_stop_usb
        ;;
  status)
	echo $"USB Status for kernel: " `uname -srm`
	echo ''

	if [ -f /proc/bus/usb/devices ]; then
	    # as noted above:  this fails on older kernels,
	    # where usbfs created files differently.
	    COUNT=`ls /proc/bus/usb | wc -l`
	    if [ $COUNT -ge 2 ]; then
		COUNT=`expr $COUNT - 2`
		echo $"USB up; bus count is $COUNT"
		grep "^[TPSI]:" /proc/bus/usb/devices
	    else
		echo $"usbfs partially up; no busses"
	    fi
	    echo ''

	    echo $"USB Drivers Loaded: "
	    if [ -f /proc/bus/usb/drivers ]; then
		cat /proc/bus/usb/drivers
	    fi
	    if [ -d /sys/bus/usb ]; then
		ls -1 /sys/bus/usb/drivers
	    fi
	else
	    echo $"usbfs is unavailable. "
	    if [ -f /proc/modules ] && grep -F -q usbcore /proc/modules; then
		echo $"USB module is loaded. "
	    else
		echo $"USB may be statically linked. "
	    fi
	    echo $"If khubd is running, that shows USB is available."
	fi
	echo ''

	if [ -f /proc/sys/kernel/hotplug ]; then
	    echo $"khubd/hotplug thread: "
	else
	    echo $"khubd thread:"
	fi
	ps -l | head -n 1
	ps -Al | grep 'khubd' | grep -v grep
	echo ''

	lsmod
	echo ''

	# /proc/devices too? "usb", "input", and others ...

	;;
  restart)
	# always invoke by absolute path, else PATH=$PATH:
	$0 stop && $0 start
	;;
  *)
        echo $"Usage: $0 {start|stop|status|restart}"
        exit 1
esac
